 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 19-3417; Rev 0; 9/04 MAX6642 Evaluation System/Evaluation Kit General Description The MAX6642 evaluation kit (EV kit) is an assembled and tested PC board with a mounted MAX6642. The EV kit allows full evaluation of the MAX6642 temperature sensor. The MAX6642 monitors its own die temperature and the junction temperature of an external diode-connected transistor. It converts the temperature to 10-bit, 2-wire serial data that may be accessed over a 2-wire serial bus. The MAX6642 EV kit includes an external diode-connected transistor (2N3906) soldered to the board, which can be removed. The board can then be connected through a twisted pair to remote diodes close to your system. The MAX6642 evaluation system consists of a Maxim Command Module (CMOD232) and a MAX6642 EV kit. The CMOD232 board connects to a computer's RS-232 serial port to provide a computer-controlled SMBusTM/ I2CTM bus. Windows(R) 95/98/2000/XP-compatible software provides a user-friendly interface to exercise the features of the MAX6642. The program is menu driven and offers a graphic interface with control buttons and status display. Order the MAX6642EVCMOD2 for a complete PC-based evaluation of the MAX6642. Order the MAX6642EVKIT if you already have a CMOD232 SMBus interface. Features Measures and Displays Temperature of the MAX6642 and the Remote Diode Programmable High-Temperature Alarms SMBus/I2C Compatible Easy-to-Use Menu-Driven Software Fully Assembled and Tested Includes Windows 95/98/2000/XP-Compatible Software and Demo PC Board Evaluates: MAX6642 Ordering Information PART MAX6642EVKIT MAX6642EVCMOD2 TEMP RANGE 0C to +70C 0C to +70C SMBus INTERFACE TYPE Not included CMOD232 Note: The MAX6642 EV kit software is provided with the MAX6642EVKIT. However, the CMOD232 board is required to interface the EV kit to the computer when using the software. Component List DESIGNATION QTY DESCRIPTION 0.1F 10%, 16V X7R ceramic capacitor (0603) Murata GRM188R71C104KA01 TDK C1608X7R1C104K 2200pF 10%, 50V X7R ceramic capacitor (0603) Murata GRM188R71H222K TDK C1608X7R1H222K 2 x 10 right-angle female receptacle Not installed 2N3906-type pnp transistor, SOT23 Central Semiconductor CMPT3906 Diodes Incorporated MMBT3906 Vishay Semiconductors MMBT3906 47 5% resistor (0603) 10k 5% resistors (0603) MAX6642ATT98 (6-pin TDFN) MAX6642EVCMOD2 (MAX6642 EV System) Component List PART MAX6642EVKIT CMOD232 AC adapter QTY 1 1 1 DESCRIPTION MAX6642 evaluation kit SMBus/I2C interface board 9VDC at 200mA (powers the CMOD232 board) C1 1 C2 1 SMBus is a trademark of Intel Corp. I2C is a trademark of Philips Corp. Purchase of I2C components from Maxim Integrated Products, Inc., or one of its sublicensed Associated Companies, conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. Windows is a registered trademark of Microsoft Corp. J1 JU1, JU2 1 0 Q1 1 R1 R2, R3, R4 U1 1 3 1 ________________________________________________________________ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 Component Suppliers SUPPLIER Central Semiconductor Diodes Incorporated Murata TDK Vishay Semiconductor PHONE 631-435-1110 805-446-4800 770-436-1300 847-803-6100 760-804-9258 FAX 631-435-1824 805-381-3899 770-436-3030 847-390-4405 760-804-9259 WEB SITE www.centralsemi.com www.diodes.com www.murata.com www.component.tdk.com www.vishay.com Note: Indicate you are using the MAX6642 when contacting these manufacturers. Quick Start Recommended Equipment Before you begin, the following equipment is needed. Do not turn on the power until all connections are made: * Computer running Windows 95, 98, 2000, or XP * RS-232 serial port (this is a 9-pin socket on the back of the computer) * Standard 9-pin, straight-through, male-to-female cable to connect the computer's serial port to the Maxim CMOD232 board * 3.3V, 100mA DC power supply 9) Wait until the program automatically detects the address of the MAX6642 and displays the userinterface panel (Figure 1). Detailed Description User-Interface Panel The user interface is easy to operate; use the mouse, or press the Tab and arrow keys to navigate. The checkboxes, edit fields, and radio buttons correspond to bits in the MAX6642 registers. Clicking on them generates the correct SMBus command and updates the registers. Note: Words in boldface are user-selectable features in the software. Procedure 1) Carefully connect the boards by aligning the 20-pin connector of the MAX6642 EV kit with the 20-pin header of the CMOD232 board. Gently press them together. 2) Disable the pullup resistors on the CMOD232 board by moving switch SW1 to the OFF position. 3) Connect a cable from the computer's serial port to the CMOD232 board. Use a straight-through, 9-pin, male-to-female cable. 4) Install the software by running the INSTALL.EXE program. The install program copies the files and creates icons for them in the Windows 95/98/2000/XP Start menu. (To remove the software at any time, click on the UNINSTALL icon.) 5) Connect the 9V adapter to the CMOD232 board. 6) Connect the +3.3V supply to the pads labeled VCC and GND on the MAX6642 EV kit. 7) Turn on the power supply. 8) Start the MAX6642 program by opening its icon in the Start menu. Temperature The MAX6642 monitors its own temperature and the temperature of an external diode. All temperature measurements are capable of either 8-bit or 10-bit (extended) resolution; 8-bit resolution results in temperature resolution of 1C/LSB. Extended resolution results in temperature resolution of 0.25C/LSB. Enable extended resolution by selecting the Enable Extended Resolution checkbox (Figure 1). Read the temperatures by clicking on the Read Temperature buttons (Figure 1). The temperature is shown to the right of the buttons. The MAX6642 has local and remote high-limit registers. Temperature exceeding the high-limit registers generates an alert interrupt. Read the high limits by clicking on the Read High Limit buttons (Figure 1). The value (in Celsius) is shown to the right of the button. Change the limits by entering the value (in Celsius) into the appropriate edit field. Pressing Enter, after typing in the new value, updates the internal register. 2 _______________________________________________________________________________________ MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 Table 1. Configuration Register Checkboxes BIT 7 6 5 4 3 2 1 0 NAME Mask alert STOP Disable local sensor Fault queue = 2 Reserved Reserved Reserved Reserved STATE Checked Unchecked Checked Unchecked Checked Unchecked Checked Unchecked NA NA NA NA Disables the ALERT interrupts. Enables the ALERT interrupts. Places the MAX6642 in software standby mode. Places the MAX6642 in operational mode. Disables local temperature measurement. Enables local temperature measurement. MAX6642 requires two consecutive faults before any ALERT is set. MAX6642 requires only one fault before any ALERT is set. Not used. Not used. Not used. Not used. DESCRIPTION External Diode The MAX6642 remote temperature sensor is optimized for use with a diode-connected transistor whose ideality factor is equal to 1.008. Transistors with different ideality factors produce different remote temperature readings. Some typical discrete transistors may produce readings that vary up to 3C from the correct value. Refer to the Maxim website (maxim-ic.com) Application Note: Compensating for Ideality Factor and Series Resistance Differences Between Thermal Sense Diodes for additional information. Status The status box displays the critical and fault conditions that occur. It also displays BUSY if the MAX6642 is performing a conversion at the time that the status is read. Each line corresponds to a bit in the registers. See Table 2 for a list of the status conditions. Read the status by clicking on the Read Status button. Note: Reading the status register clears the alert interrupt. Alert The message ALERT appears in the Alert box when an interrupt condition occurs unless the configuration register is set to mask the alert. The cause of the interrupt is shown in the status boxes. To clear the interrupt, first eliminate the condition that caused it and click on Read Alert. Note: Reading the status register also clears the alert interrupt. Configuration The configuration register has several functions. Figure 1 shows the checkboxes that configure the register. Each checkbox corresponds to a bit in the register. Table 1 describes the function of each checkbox. Read the configuration register by clicking on the Read Configuration button (Figure 1). The checkboxes are either checked or unchecked to correspond to the bits in the register. Table 2. Status Register BIT 7 6 5 4 3 2 1 0 BUSY Local high Reserved Remote high Reserved Diode OPEN Reserved Reserved NAME DESCRIPTION The MAX6642 is performing a conversion at the time that the status is read. The temperature of the MAX6642 is above the value set in the local high-limit register. Not used. The temperature of the remote diode is above the value set in the remote high-limit register. Not used. Remote diode is open. Not used. Not used. _______________________________________________________________________________________ 3 MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 Single Shot The single-shot command immediately forces the MAX6642 to begin a temperature-conversion cycle. Refer to the MAX6642 data sheet for more information on the single-shot command. The single-shot command does not read the local or remote temperature registers. Read the temperature registers by clicking the Read Temperature buttons or by selecting Read All on the Action menu. Simple SMBus Commands There are two methods for communicating with the MAX6642: through the normal user-interface panel or through the SMBus commands available by selecting Interface on the Debug menu. A display pops up that allows the SMBus protocols, such as read byte and write byte, to be executed. To stop normal user-interface execution so that it does not override the manually set values, turn off the update timer by deselecting Automatic Read on the Action menu. The SMBus dialog boxes accept numeric data in binary, decimal, or hexadecimal. Hexadecimal numbers should be prefixed by $ or 0x. Binary numbers must be exactly eight digits. Note: In places where the slave address asks for an 8bit value, it must be the 7-bit slave address of the MAX6642 with the last bit set to 1 for a read operation and zero for a write. Automatic Read The program polls the device for new temperature and status data a maximum two times a second (2Hz). To disable the polling of data, deselect Automatic Read on the Action menu. Note: The program does not automatically read the status register during an alert interrupt. Reading the status register clears the interrupt. Data Logging Select Data Logging on the Action menu to activate data logging. Data logging saves temperature, voltage, and status data to a text file that includes a time/date stamp next to each data point. If automatic read is enabled, data is sampled at 2Hz; however, the data is logged to the file only if the temperature or status has changed. This slows the growth of the data-logging file. When automatic read is disabled, the data is logged each time Read All is selected on the Action menu. To stop data logging, deselect Data Logging on the Action menu. Jumper JU1 Jumper JU1 connects the 2N3906 transistors as the external diode. To use a different diode, cut the trace, short the two pins of JU1, and connect the diode (through twisted-pair wire) to the pads labeled DXN and DXP on the MAX6642 EV kit. Jumper JU2 Jumper JU2 connects the ALERT line to VCC through pullup resistor R4. The CMOD232 interface board has a pullup on ALERT and does not require the pullup resistor on the MAX6642 EV kit. Place a short across JU2 when using an SMBus interface board that requires the pullup resistor on ALERT. 4 _______________________________________________________________________________________ MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 Figure 1. Main Window for the MAX6642 EV Kit Software _______________________________________________________________________________________ 5 MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 J1 VCC J1-1 JU2 ALERT VCC VCC R1 47 C1 0.1F 1 2 JU1 DXP C2 2200pF SCLK 3 DXP 4 2 GND 1 VCC U1 ALERT 6 VCC SMDATA J1-9 J1-11 SMDATA J1-13 VCC SMBCLK R2 10k J1-15 J1-17 J1-19 N.C. N.C. N.C. J1-16 J1-18 J1-20 N.C. J1-14 N.C. ALERT J1-10 J1-12 R4 10k J1-5 ALERT J1-7 SMBCLK J1-8 J1-6 J1-3 N.C. SMBDATA J1-2 J1-4 GND Q1 3 MAX6642 5 R3 10k SDA DXN SMBCLK Figure 2. MAX6642 EV Kit Schematic 6 _______________________________________________________________________________________ MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 Figure 4. MAX6642 EV Kit PC Board Layout--Component Side Figure 3. MAX6642 EV Kit Component Placement Guide-- Component Side _______________________________________________________________________________________ 7 MAX6642 Evaluation System/Evaluation Kit Evaluates: MAX6642 Figure 5. MAX6642 EV Kit PC Board Layout--Solder Side Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. |
Price & Availability of MAX6642EVKIT
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |